Changing the LED lights inside your preferred controller is fairly easy. For each controller you will require a reasonable electrical power soldering iron, 60/40 rosin, a sponge, a pair of pointed tweezers, and your brand-new LEDs. You could utilize a greater electrical power iron, but it is safer to start with a reasonable watt so you prevent possibly destroying your motherboard. To open a 360 controller, you will require a t8 screwdriver. A small Phillips head screwdriver is used for the ps3. When taking the screws out of the 360 controller there is a hidden screw discovered inside the battery pack terminal behind the oblong shaped bar code sticker.
To begin you will should tin the soldering iron. This merely implies to melt rosin on the iron and then cleanse it off with your sponge. When cleaning the iron, I located it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to increase contact.
As soon as you have the screws gotten there are a couple of steps you will want to avoid breaking your controller case. To dismantle the xbox 360 controller, you will have to push in the thumbsticks and carefully pry the controller apart. To prevent losing any of your buttons, I recommend applying a strip of tape to the front of the controller to hold everything in place. After you have done this, you will have to pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather much easier to disassemble. Once you have the screws removed, you will just pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that links the R's and L's off their clip. You are now prepared to remove the old lights from the motherboard.
To remove the LEDs, I like to use a method called floating. To do this, you will should thaw some rosin on the iron until it makes a little bit of bubble on the iron itself. It may look like it is going to fall off, but do not stress, it will remain on the iron. As soon as you have this done, you will drift the bubble backward and forward throughout the LED to remove it. This will most likely take simply a few seconds and the LED will stick to the rosin. Then you will simply clean the iron off and duplicate the process for each light.
Applying the new LEDs is a little more difficult than taking them off. Initially, you will have to consider all-time low of the brand-new LED and determine which side the arrow on the bottom is pointing. You will have to point the arrow towards the negative side of the motherboard. If you can not figure this out, turn the power to the controller on and the LED will light up if you have actually properly lined it up. I such as to leave the battery pack and the back half of the controller connected. This is so I could use the contact pad to turn the controller on. For the ps3, you could simply plug in the charging cable television. When you have actually aligned them properly, you will use your tweezers to hold the LED in place and simply add a little bit of rosin to both side and you are done. It might take a while however a little bit of practice will make things a lot simpler. Now you prepare to flaunt your freshly light controller with your most loved color lights!
To begin you will should tin the soldering iron. This merely implies to melt rosin on the iron and then cleanse it off with your sponge. When cleaning the iron, I located it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to increase contact.
As soon as you have the screws gotten there are a couple of steps you will want to avoid breaking your controller case. To dismantle the xbox 360 controller, you will have to push in the thumbsticks and carefully pry the controller apart. To prevent losing any of your buttons, I recommend applying a strip of tape to the front of the controller to hold everything in place. After you have done this, you will have to pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather much easier to disassemble. Once you have the screws removed, you will just pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that links the R's and L's off their clip. You are now prepared to remove the old lights from the motherboard.
To remove the LEDs, I like to use a method called floating. To do this, you will should thaw some rosin on the iron until it makes a little bit of bubble on the iron itself. It may look like it is going to fall off, but do not stress, it will remain on the iron. As soon as you have this done, you will drift the bubble backward and forward throughout the LED to remove it. This will most likely take simply a few seconds and the LED will stick to the rosin. Then you will simply clean the iron off and duplicate the process for each light.
Applying the new LEDs is a little more difficult than taking them off. Initially, you will have to consider all-time low of the brand-new LED and determine which side the arrow on the bottom is pointing. You will have to point the arrow towards the negative side of the motherboard. If you can not figure this out, turn the power to the controller on and the LED will light up if you have actually properly lined it up. I such as to leave the battery pack and the back half of the controller connected. This is so I could use the contact pad to turn the controller on. For the ps3, you could simply plug in the charging cable television. When you have actually aligned them properly, you will use your tweezers to hold the LED in place and simply add a little bit of rosin to both side and you are done. It might take a while however a little bit of practice will make things a lot simpler. Now you prepare to flaunt your freshly light controller with your most loved color lights!
No comments:
Post a Comment